Jump to content

Book washing machine & appliance repairs

Ransom Spares

Note: The links above are needed to help keep this site running, please consider using them.

uas66

AEG washing machine shock absorbers

Recommended Posts

Hi all,

This week I have replaced the shock absorbers of my AEG Lavamat 74530. The old shock absorbers were completely worn out. When I held the old shock absorbers upside down, they already fell down.

The new shock absorbers are somewhat difficult to move by hand. Is it normal that the new shock absorbers can also be moved in and out by hand or are they so strong that it is not possible?
I am asking this because I am not sure whether the new shock absorbers are defective. When the machine is spinning with washing, the washing machine still makes a little noise.

I also discovered that a hole through which the spring is sitting is completely worn out, so that the spring was no longer stuck. The drum had a hole in front of it in which I placed the spring. I also moved the spring to the other hole on the other side.

Could it be that the 2 springs at the top no longer function correctly or is it because of the wooden floor / legs of the machine on which they are placed? The leg at the rear left is a leg with a spring. When I press on the top it goes down and when I no longer press, this side comes up again automatically.

Hope someone can make me wiser! Thanks in advance!

10413_IMG_3330_1.jpg

10413_IMG_3331_1.jpg

Share this post


Link to post
Share on other sites

Book washing machine & appliance repairs

Ransom Spares

Note: The links above are needed to help keep this site running, please consider using them.

Hello. The outer drum should depress when you put pressure on it and then return to normal. The suspension legs should be quite stiff and strong. They need to take the weight of the drum full of washing and water bouncing around and absorb the movement. If the part on the outer drum that the suspension damper fits into is broken though you are going to have problems. The only fix is a new outer drum. If you've managed to hook the spring onto a similar hole close by it might hold but it may allow the drum to twist. That could cause wear on the door seal or other parts and may affect how stable it is on spin.


Need an engineer, or to buy appliance spare parts? Please use my affiliate links to support this forum.

Book appliance engineer | Buy your appliance Spares 

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Share this post


Link to post
Share on other sites

Thanks for your reply. The holes for the shock absorber are just fine, the problem is with the hole from the suspension springs.

As you can see at the second photo you can see where I mounted the spring in the other hole (you can also see the hole at the first photo). Do you think this makes any difference to the machine? Right and left side are now on the same hole.

I think the hole was worn out because of the bad shock absorbers. The drum was beause of this going to low what caused the plastic hole to worn out.

Share this post


Link to post
Share on other sites

Hi, yes I meant the springs. The springs need to hold the drum central inside the casing and I would expect if you moved one over to the other hole it would cause the drum to twist slightly, especially with a heavy load inside. Wondering if you swapped the spring on the other side over so that both springs are on the opposite hole would that even things up?


Need an engineer, or to buy appliance spare parts? Please use my affiliate links to support this forum.

Book appliance engineer | Buy your appliance Spares 

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Share this post


Link to post
Share on other sites

Yes, I also swapped the other spring to the other hole so both springs are on the same hole.

Could the problem be caused by the floor? The washing machine is on a wooden floor and the floor is a little flexible. The rear left feet is a feet with a spring. When I press on the top it goes down and when I no longer press, this side comes up again automatically.

PSGBAP170PW000A1.jpg.24931633e8caca25c44cc1f4e518d0f1.jpg

Share this post


Link to post
Share on other sites

Hello there. Uneven or springy floors usually cause the washing machine to move about a bit on spin. It wouldn't normally cause the washing machine to break down.


Need an engineer, or to buy appliance spare parts? Please use my affiliate links to support this forum.

Book appliance engineer | Buy your appliance Spares 

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...