Jump to content
John Lewis give 2 year guarantee on white goods appliances

 

LG washing machine WD16223FD shock absorbers


Recommended Posts

Hello there,

I recently replaced the bearings on the tub of my LG WD16223FD.

After putting everything back I realized that one of the shock absorber is pressed completely down and making loud noise during spin cycle. So I went ahead and bought a new one.

After installing the new shock absorber, it is also completely pressed and makes loud noise. You can see that in the attached video.

Now there could be 2 possible reasons for it

  1. the new shock absorbers are also bad (fake) OR
  2. I did something wrong while putting the drum back together.

The right (white) is the new one. The black is the original one.

What could be the problem? I am out of ideas :(.

Thanks!
Tathagat

Link to post
Share on other sites

Did you definitely fit them the right way around? The washing machine suspension dampers sometimes have different requirements for left and right sides. This is because when the drum spins there is extra force put on the damper that takes the force of the drum spinning around. So for example if the drum spins clockwise when looking from the rear then the damper on the right (looking from the rear) should be stronger.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

Hi Andy,

thanks for the reply. I bought 2 new ones. They both are identical. So I am unable to choose the stronger one.

Another thing that I note is that the drum is hanging lower than it should. I can see it from the front as the rubber is hanging. Do you think that the springs on the top might have worn off cause it to press down on the dampers?

 

Cheers
Tathagat

Link to post
Share on other sites

Springs on the top shouldn't need replacing. Did the original dampers have different colours on them? If they should be the same they should look identical. But if one has a coloured spot or other marker on it then that strongly implies they have different strengths and need replacing with the same colour. I can't imagine how one damper could be so badly out of line though. It's not upside down is it? I wouldn't have thought it possible for one to move over so far. 

It's not easy to see much on the video apart from how badly out of line the left one is. If you could post a decent photo or two of the back and looking from the top I might be able to spot something.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

Hi Andy,

both dampers look exactly the same. Today I put the older one back in as the newer one made it worse. So I could recheck. It's not upside down for sure. I never took it off completely in the first run. Only took the connector from the drum off so there is no way it could be wrongly oriented.

Please find some pictures from the back and top on this URL

https://photos.app.goo.gl/6rvEZJazE5v9jHKe8

Also a picture from the front showing that the tub is hanging a little lower than it should.

I don't know what I could have done wrong while putting everything back. All I did was replaced the bearings and put everything back together where it belongs.

Cheers and thanks!
Tathagat

Link to post
Share on other sites

It looks like the fixing bracket on the tub for the left suspension damper is in the wrong place. The tub also looks twisted. Are the top springs fitted right? One has a yellow mark on it which indicates it's different from the other and designed for one side only. It's a shame you didn't take photos before you stripped it down, that's one of my number one recommendations.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

Also it seems strange that the spring on the right as looking from the front top is attached to a different type of bracket than the one on the left.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

I THINK YOU GOT IT!!!!

I have connected the right spring (the one with yellow marking) in the wrong slot. Sh*******T. I am lucky that it did not break! I confirmed it by looking at the video I followed to change the bearings.

Right now a washing is running. As soon as it is done, I guess I will have to open the machine again, take down all the weights and then reattach it in the right slot. Or do you think I can do it (re-fit the spring) with care without opening everything up again?

THANKS YOU SO MUCH!

  • Like 1
Link to post
Share on other sites

Excellent. I would stop the washing machine! Letting it spin with laundry inside and the drum so twisted, and with the suspension not working - you could do some serious damage to the washing machine.

After that, totally drain the water and disconnect from the mains. Then lay the washing machine down on its front and try to sort the top springs out.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

No it won't break. Just keep the door shut. Make sure you drain the water out properly by lowering the drain hose into a bowl so water doesn't run out onto electrical parts.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

I just went ahead and took the weight off (I have done this 4 times in 1 week - so I am really fast in it now ;)) and fixed the spring in the right hook and MAGIC. It works perfectly. :)

I can't thank you enough!

Let me know if I can donate some money to the forum!

Thanks a ton again :)

Cheers
Tathagat

  • Thanks 1
Link to post
Share on other sites

Excellent news. Glad to have helped. I used to have a donation link but I took it down when I started using white goods related ads for spares, repairs and buying etc. If you need to buy spares or book an engineer etc just consider trying one of my links in the future thanks.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

As the drum weights have been on an off a lot, make sure you listen out for knocking noises over the coming months and from now on. If locking nuts were used (nuts with plastic inside) they may not hold as well and slowly come loose. If so and ignored the weights will rip the brackets off the plastic outer drum.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

No worries. The fixings are under enormous pressure during spin as the drum weight is trying its best to get thrown off. Without loctite or locking nuts they will come loose.

Need a repair or spare parts? 

Book a Repair | Buy Spares (Cheapest prices guaranteed)

Warning:  Read this before attempting any diy repairsNo representations or warranties are made (express or implied) as to the reliability, accuracy or completeness of advice. I can't be held liable for any loss arising directly or indirectly from the use of, or any action taken in reliance on, any information on this website, which is given free of charge and in good faith.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Book your Repair

Book washing machine & appliance repairs

Order your Spares

Ransom Spares is a family company with over 1 million white goods appliance spare parts for sale. Next day delivery available, friendly company with over 5000 reviews on Trust Pilot

Price match promise: "If you find the exact same part or accessory elsewhere for cheaper, we’ll not only match it, we’ll beat it!" -

Buy your appliance spare part



×
×
  • Create New...