Philip 0603

Thanks for the help Andy, will post again when I have fixed the machine. This may take a bit of time as I have swapped the machine out for another spare one. Yes I am sad and have three automatic washing machines. This one is an old Tricity Bendix 7179 compact washer that I use if putting the caravan on a seasonal pitch. It is so small that I can carry it around, though I don't know exactly how old it is it still works as it should. No electronics in sight just pure mechanicals.

Thank you Andy for your help. I will initially try the Thermistor as this problem started after a hot wash. As far as the difference between drum action top loaders and standard front loaders is concerned, the way I see it is the componentry is the same; just an alternative way of introducing clothes into the drum. One small advantage of the top loader configuration is the drum is supported on both sides thus bearing failure is reduced.

HI and thank you for the reply. I have just been out and run the machine again and this is what it does in the sequence it does it in. . Close lid, (forgot to say it's a drum action top loader) select program then the lights do the following. Power on light lights, then slow flash till the lid lock engages after a few seconds or so, then the power on light flashes 4 times rapidly then comes on steadily for a few seconds. it does not repeat the flashing. The machine then switches off the power indicator light, starts to rotate the programmer dial and switches on the pump. At no point does the drum rotate. The power light then comes on once per sector as the dial passes the rinse symbol of each third of the dial. I am hopeful that the fault lies with the fact the washer has not been used for so long and is throwing wobblies at having to work. Thanks in anticipation.

Miele's do this too. I am now on my third glass. The scratch is superficial and in my case have not affected the glass or the washer in any way. Just occasionally my machine will have a fit and ramp up the spin too quickly without distributing the clothes around the drum. PS the machine was over £1300 when I bought it 9 years ago, but considering the hammer it has received I am so glad I bought it.

With regard to detergent and towels, this was told to me when I bought my Miele by the engineer chappie that fitted it:- When doing towels, especially the heavy luxury ones always use HALF the amount of detergent that you would normally use. After all the point of the towel is to dry you down and now matter how well you shower there will always be some shower gel left on you which the towel absorbs. Also note that most machines recommend you reduce the load. Also note that a small load of towels will 'foam' up rather easier than a full load of mixed fabrics. Obviously never ever use fabric conditioner near a towel. Though having said that one way of getting rid of the suds if the machine has over foamed is to pour a bit of conditioner into the machine through the drawer and rinse down with a small amount of water. A cap full will reduce the foam for long enough to empty the machine with it's pump.

Hi to all. As a newbie on theis forum I humbly ask for some help with my washing machine. Firstly have had a look in the washing machine fault FAQ's which were most helpful, though did not solve the problem, though may point to a solution, just need to ask before I spend money I have'nt got. I have an Indesit WT82T of 2002 vintage. It is very similar to the Hotpoint WTL500P though with 800 spin speed. The machine was installed in a property in France for about 6 months then put into storage for 9 years. Having read the section on fault codes I proceeded to see if the machine would be forthcoming and give me one. Any way this is what it does. Set the programmer to a spot/cancel programme position on the dial, close the lid and switch on. Mains light flashes slowly whilst the lid lock is enaging then 4 (I think) rapid flashes then it goes out and the machine starts pumping out and a few seconds later the programmer starts to roatate. No matter what I do I can not re-set the programmer. The light does come on agin breifly as the programmer passes the rinse section of each of the programme areas. Reading your fult code section it has been suggested that this could be a thermistor (what ever one of those is). I am a reasonably competant diy-er and wonder if I could replace the offending part myself. Your advice would be greatly appreciated, I am sure I can obtain a spare part even though the machine is a French model. Thanking anyone in anticipation.